Seat Alhambra Key Problems
Seat's Jumbo MPV family is among the top in its class when it comes down to resales value. With a new model available for sale the family MPV jumbo is better.
There are many reasons why your key fob could not function properly including dead coin battery water damage, receiver module issues or signal interference. This article will guide you through the steps to make sure it works.
Water Damage
If your key fob for the seat alhambra can withstand an wash cycle, a dip in the ocean or a pool then it has a waterproof chip. But be G28CarKeys not to do this often because prolonged exposure to water can increase chances that the key fob will be damaged. If your key fob stops working after exposure to rain or clean tap water, take out the battery and wipe the electronic component using a paper towel. Dry it completely before replacing the battery. If the key fob was exposed to soapy or salty water, it is recommended that you clean the chip using isopropyl or an electronic cleaner.
Faulty Receiver Module
If the key fob does not lock or unlock after you have replaced the battery for the button It is possible that the receiver module is suffering from an issue. The good news is that it is a relatively simple and affordable fix, you can remove the battery 12 volts for several minutes (first remove the negative cable, then press the horn button numerous times) to eliminate any remaining electricity and then reconnect it in reverse order e.g. Positive first followed by negative.
ESP Warning Light - If the ESP symbol is flashing, this is normal. It is a sign that you are driving on terrain with poor traction. This could be due to gravel, snow or surface water. If the ESP warning light remains illuminated it indicates that there is an error within the system. This can be detected with a iCarsoft i908 Seat OBD Code Reader, which will provide you with a specific fault description.
Dead Coin Battery
One of the most frequent reasons for the seat alhambra keys to stop working is a dead coin battery. The key fob comes with a small button cell battery which keeps it powered. It should be replaced by a new battery that has the same size, voltage, and specification as the original. When replacing the battery on the key fob, remove the metal clips and make sure that the contacts of the key fob are clean and corrosion-free.
If the key fob has been exposed water, such as rain or soapy water, it's recommended that you take the battery off and clean the electronic chip using isopropyl alcohol or an electronic cleaner prior to installing the new battery. The chip is sensitive to moisture and can be permanently damaged. If the key fob doesn't work after replacing the battery, it may be necessary for you to replace the key fob.
Faulty Receiver Module
If your key fob stopped working after you replaced the battery, but it didn't help, or if it stopped working completely without notice The receiver module could have developed a fault. The receiver module is responsible for receiving the radio frequency signals transmitted by the remote key fob and convert them into electrical signals that are then acted on by other modules in your car.
If the receiver module has developed a fault that prevents it from responding to any of the commands issued by your remote key fob. In this case you will require a dealer to reprogramme the key fob and install a new receiver.
The key fob is sealed with rubber to stop water from getting inside the electronic chip. However, if you submerge your key fob in soapy water or salty ocean water, the chip inside could be damaged. You can attempt to clean the chip by applying isopropyl alcohol or electronic cleaner, however If your key fob doesn't work after doing this, you'll have to buy a new one.
If the keys are paired but the receiver module has developed a fault you may try to restart all of the onboard electronics by removing the battery that is 12 volts for a short period of time. Connect the battery in reverse (negative cable to positive first). This will reset the onboard electronic circuits and restore their functionality.
A malfunctioning electronic chip
The key fob comes with a tiny chip that transmits an indication from the key to the receiver module each time the key is used. If the signal isn't in line with the one the car has stored the immobilizer will be disabled and prevent the vehicle starting. If, however, the key fob isn't working, and you can't reprogram it then it could be due to a defective chip.
The chip inside the key fob isn't a permanent part of the device, and might need to be replaced in order to get it to work again. The best method to do this is by removing the key from its housing and then using a pin or needle to contact each of the clips made of metal. If these are corroded or damaged, you'll need to replace them to allow the remote control to work. Make sure that the replacement batteries are the same voltage, size and specification as the original.
The Seat Alhambra is a well-designed and popular car however, just like any other vehicle it may encounter problems with specific parts or equipment. A few owners have reported issues with the climate control system that is automatic. It is prone to fail and get stuck in a particular setting. The infotainment system can also malfunction and freeze the screens.